• RCR1884 Rotary Cutters

RCR1884 Rotary Cutters

RCR1884 Rotary Cutters

Available Models

RCR1884

Description

Land Pride’s RCR1884 Series Rotary Cutter offers an 84" cutting width to rapidly tackle material up to 2" in diamater for light maintenance around the farm, the pond or empty lots in the city. The cutter has a Category I and Category II three-point hitch and is Quick Hitch compatible. It is offered with a standard ASAE Category 4 driveline with slip-clutch protection and a single or dual rear laminated tailwheel.

Features and Benefits

FEATURES BENEFITS
Surpassed rugged industry standards All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures specified by ANSI.
90 Hp gearbox A rugged heavy built gearbox capable of handling heavy cutting applications.
5 Year gearbox warranty Shows our confidence in the gearbox integrity.
Cat. 4 driveline with 2-plate slip-clutch Slip-clutch driveline offers convenience for continual work.
Cat I or Cat II Hitch Quick Hitch Capability Permits deck to follow the terrain for an even cut. Quick Hitch provides for fast hook-up.
Lower clevis type 3-point hitch Allows for ease of hook-up to tractor. Also adds additional strength allowing for an even pull from the tractor’s lower arms, vs. pulling on a single pin design.
84” Cutting width Wide cutting width, Reduces cutting time in the field.
Heavy 10 gauge deck construction Can withstand more abuse than lighter gauge decks.
Box tubing deck supports Makes for a stronger rigid deck.
Fully welded deck Adds additional strength.
Extended cutter front For increased material flow and added protection
Round back design Helps discharge grass better than enclosed or partially enclosed cutter.
9 1/2” Deck Height Allows cutter to handle heavy cutting conditions.
2” to 11” Cutting height Provides for a wide range of cutting conditions.
1/4” x 2 1/2” Full length skid shoes Provides sidewall reinforcement and full protection to bottom of sidewall.
1/2” x 4” Heat-treated free swinging blades Free swinging protects from obstructions. Heat-treated offers longer life.
Splined blade bar hub Allows for tight positive fit of stump jumper and blade bar to gearbox output shaft.
10 Gauge stump jumper Standard oval stump jumper slides over stumps, rocks and debris.
High blade tip speed Ensures clean cut. (17,113 FPM)
2” Cutting capacity Can aid in cleaning brush
Available with single or dual tailwheels Dual tailwheels offer greater stability in uneven terrain.
15” Laminated tailwheel Laminated material is long lasting in rough conditions.
Heavy-duty spindle on tailwheel Tailwheels take a beating, 1 1/4” spindle gives the strength to protect tailwheel assembly.
Guarding Protect against flying debris. Customer must choose to include chain or rubber on the front and rear. Rear Metal band standard.

 

Download Features and Benefits

Download features and benefits of this product here:  312-880f.pdf

Download Specifications

Download the Product Specifications here:  312-880s.pdf

Operator's Manual

Download a PDF of the Operator's Manual here:  312-880m.pdf

Parts Manual

Download the Parts Manual here:  312-880p.pdf

Download Accessory Manuals

The following accessory manuals are available for download:

Warranty

Overall Unit and Driveline: One year Parts and Labor
Gearbox: 5 years Parts and Labor
Blades, tires and driveline friction discs: Considered wear items

See complete Warranty Statement below.

Download Complete Warranty

Download the full Product Warranty here:  312-880w.pdf

Frequently Asked Questions About This Product

Why is by tailwheel/gauge wheel not pivoting properly?
Answer

The gauge wheel spindle tube could be locking up. Make sure that the spindle tube is grease at a minimum of every 24 hours of use. The gauge wheel hub needs to be greased every 8 hours of use.

Why do I keep breaking my tail wheel yoke?
Answer

Grease tailwheel and yoke per manual instructions as it is likely becoming stuck.

Why did the shear bolt break on my driveline?
Answer

The shear bolt is in place to protect the gearbox from damage. The shear bolt is designed to shear when the blade impacts foreign objects that it is not designed to cut through. To avoid shear bolt failure, engage the PTO slowly at low engine RPM. Shear bolt should be replaced with Grade 2 bolt.

Why are my cutter blades locking up?
Answer

Ensure that your cutter is being engaged and disengaged at an idle speed. Check that the tractor has a hydraulic engage oil clutch. Blades may also need to be reshimmed. The mower blades need to be less than ¾” deflection.

What is causing my cutter to vibrate?
Answer

Your blades may need to be weighed, and checked for damage. The dishpan also needs to be checked for damage (from a forklift, stump, etc.)

What do I need to do if my cutting height is off or my deck is lower at the front than at the back?
Answer

You will need to raise or lower the tailwheel height. To lower the cutting height, adjust the tailwheel up. To raise the cutting height, adjust the tailwheel down.

What do I do if I break the shear bolt when I start the tractor?
Answer

Start your cutter with the tractor at idle and no load on cutter.

What could be causing my cutter to vibrate?
Answer
  • The cutting blades could be out of balance. Be sure to replace both cutting blades at the same time. Not replacing both blades could result in premature bearing damage or structural damage to gearbox or deck.
  • Dishpan could be out of balance. Check the integrity of the dishpan. Make sure it does not have any damage.
What caused the tailwheel support to fail?
Answer

Lowering the cutter to the ground too fast can cause the tailwheel support to fail. The rate of drop on some tractors can be adjusted. Backing up when the cutter is in a ditch can also cause the tailwheel support to fail.

What caused the driveline to bend or twist?
Answer

Either the slip clutch was never slipped, or a grade 5 or grade 8 bolt was used in place of the grade 2 bolt specified.

What are check chains?
Answer

Check chains are used when you want to return the mower down to the same height of cut every time.

The u-joint has come apart. Why?
Answer

If you have a Slip clutch driveline: Pre slip clutch per manual instructions.

If you have a Shear bolt driveline: Use grade 2 shear bolt.

My driveline will not slide or telescope?
Answer

Grease driveling profile also check to be sure the profiles are not bent.

How do I remove the blades on my cutter?
Answer

Rotate the dishpan until the blade bolt aligns with the access hole. The blade bolt is keyed so it will not rotate freely. You will need to unscrew the lock nut to remove cutting blades.

How do I drain the oil in the gearbox?
Answer

Remove the vent plug (if on top) and use a suction gun to pull the oil out. If the vent is on the side or back, the top cover can be removed and then the oil can be removed with the suction gun.

Product Literature

Download product literature here:  lit_rcr18.pdf